8x10 Shed Material List
The complete, pre-calculated material list for a 8×10 gable-roof shed with 8-ft walls — every stud, sheet, and bundle you need to buy.
Last updated: May 2026
An 8×10 shed adds just enough depth over an 8×8 to store bicycles alongside your garden gear. The 80-square-foot footprint fits two or three bikes, a mower, and shelving along one wall, and it still slips under the permit threshold in many municipalities. The list below covers a 8×10 footprint (80 sq ft) and assumes 8-foot walls, a gable roof at a 6/12 pitch, walls framed 16 inches on center, and a framed plywood floor. Every quantity is computed with the same formulas as our shed material calculator — if you want to adjust dimensions or roof style, run your own numbers there.
Complete 8×10 Shed Material List
| Material | Quantity | Est. Cost (Low–High) |
|---|---|---|
| Wall Studs (2×4×8) | 31 studs | $93 – $248 |
| Top & Bottom Plates (2×4×8) | 14 pcs | $42 – $112 |
| Wall Sheathing (4×8 OSB) | 9 sheets | $225 – $540 |
| Rafters (2×6) | 12 pcs | $60 – $144 |
| Roof Sheathing (4×8) | 4 sheets | $100 – $240 |
| Asphalt Shingles | 3 bundles | $75 – $150 |
| Roofing Underlayment | 1 roll | $25 – $45 |
| Floor Joists (2×6) | 9 pcs | $45 – $108 |
| Floor Plywood (3/4" 4×8) | 3 sheets | $75 – $180 |
| T1-11 Siding (4×8 sheets) | 9 sheets | $270 – $585 |
| Pre-Hung Door | 1 | $100 – $350 |
| Fasteners & Hardware | 1 lot | $50 – $120 |
| Total | $1,160 – $2,822 |
Prices are approximate U.S. averages — the same unit prices our shed calculator uses — and vary by region, retailer, and lumber market conditions.
How Much Lumber for a 8x10 Shed?
A 8×10 shed with 16-inch on-center walls needs about 31 wall studs plus 14 eight-foot 2×4s for the top and bottom plates. The gable roof takes 12 2×6 rafters at 24-inch spacing, and the floor frame uses 9 2×6 joists at 16 inches on center. For sheet goods, plan on 9 sheets of OSB for wall sheathing, 4 sheets for the 98 sq ft roof deck (including overhang), and 3 sheets of 3/4-inch plywood for the floor — 16 sheets in total — plus 9 sheets of T1-11 siding and 3 bundles of shingles. Buy two or three extra studs for blocking and door framing, and cull any badly crowned boards for cut-up pieces.
Foundation for a 8x10 Shed
A gravel pad should extend 12 inches beyond the shed on all sides, so a 8×10 shed needs a 10×12 gravel pad. At 4 to 6 inches deep, that works out to about 1.8 cubic yards of compacted 3/4-inch crushed stone over landscape fabric — fine-tune the gravel quantity here. If you would rather pour a concrete slab, a 8x10 slab at 4 inches thick takes about 1.0 cubic yards of concrete — roughly 45 80-lb bags if you mix it yourself. Estimate the concrete for a slab here.
Estimated Total Cost
Expect DIY materials for a 8x10 shed to run $1,160 to $2,822. The low end assumes basic framing lumber, OSB sheathing, and 3-tab shingles; the high end reflects plywood sheathing, architectural shingles, and premium siding. That total does not include the foundation, paint or stain, a ramp, or shelving. For a full comparison of DIY builds against shed kits and professional installation, see our shed cost guide.
Frequently Asked Questions
Materials for a 8x10 shed with 8-foot walls, a 6/12 gable roof, and a framed plywood floor run about $1,160 to $2,822. The low end reflects basic framing lumber, OSB sheathing, and 3-tab shingles; the high end reflects plywood sheathing, architectural shingles, and premium T1-11 siding. Foundation materials, paint, and interior shelving are extra, and hiring a contractor to build it adds labor on top of materials.
A 8x10 shed with 8-foot walls and a 6/12 gable roof needs about 16 sheets of 4x8 sheet goods in total: 9 sheets for wall sheathing, 4 sheets for the roof deck, and 3 sheets of 3/4-inch plywood for the floor. Use OSB for walls and roof to save money, but stick with plywood rated for flooring on the deck.